Junsi icharger x8 manual

Follow the instructions below for the complete process with the SD card. Firmware upgrades via SD Card. 1. Create a new directory in the available SD card: X:JunsiUpgrade ; 2. Rename the firmware file to X6.BIN, and copied to the new directory; 3. Insert the SD card into the charger and then enter Boot mode. The Junsi iCharger X8 Lilo/LiPo/Life/NiMH/NiCD DC Battery Charger features 8S capabilities and up to 1100W of power and up to 30 Amps of charge current. Features: X8 uses advanced Synchronous buck-boost DC/DC converter technology with high power, high current and high-performance power conversion circuit. The maximum charge power capacity is up to 1100W, the maximum charge/discharge current of a channel is up to 30A. X8 Supports 8s LiPo, Lilo, LiFe, LiHV, LTO and NiZn batteries, with maximum 2A balance current, and adopts a unique balance calculation of internal resistance correction. Supports 1-25s NiMH/NiCd batteries and 1-15s Pb batteries. The Junsi iCharger X8 Lilo/LiPo/Life/NiMH/NiCD DC Battery Charger features 8S capabilities and up to 1100W of power and up to 30 Amps of charge current. X8 uses advanced Synchronous buck-boost DC/DC converter technology with high power, high current and high-performance power conversion circuit. The maximum charge power capacity is up to 1100W Your iCharger is calibrated in the factory before it is shipped. If you find there is need for calibration, you can calibrate your iCharger using the steps covered in this article. All electronic devices wander over time and it is important to make sure that your icharger is still working with accurate voltage. iCharger uses its voltage reading The iCharger X8 Lilo/LiPo/Life/NiMH/NiCD DC Battery Charger features 8S capabilities and up to 1100W of power and up to 30 Amps of charge current. Clicke here to Download iCharger X12 Manual. The iCharger X12 is a new Junsi product launched in fall of 2020. This palm-sized charger is packed with an unbelievable 1100W 30A of power packed Essential for long term storage and care of the battery. iCharger 208B is a true 20amp battery charger. Boasting 350w of power which ensures that 20amps is available no matter what size the battery is being charged. Most "amp" ratings on other charging products available are not an accurate representation. The iCharger S6 is a new Junsi product launched in fall of 2020. This palm-sized charger is packed with an unbelievable 1100W 40A of power packed into a miniature frame, replete with features only seen in advanced chargers. The charger shares the accessible and easy-to-understand user interface found in the popular Duo iChargers. Buddy RC has been a major iCharger distributor since 2009, and Junsi iCharger X8 1x output cable 3.3 mm² with XT60 socket 1x input cable 3.3 mm² with XT60 socket Installation CD with software and instructions in english Printed german manual; Average product review Write your first review and help others with their purchase decision: Contact. First name. Last name. Firm. E-Mail. Phone New iCharger X6 and X8 Has Been Released! New iCharger X6 has been released. It is a mini balance Charger/Discharger/DC Power with high power, high current and high-performance power conversion circuit for LiPo、Lilo、LiFe、LiHv、LTO、NiHM、NiCd、NiZn and Pb batteries. The iCharger X8 Duo is a dual port AC/DC charger that can handle 8S packs. The maximum charge power capacity is up to 1600W, the maximum charge/discharge current of a channel is up to 50A, and two